SKF推力軸承主要應用于汽車、機床等行業。所以對軸承的安裝一定要非常的小心，因?yàn)槿绻隽藛?wèn)題就一定會對我們生活造成很大的影響。接下來就讓我來告訴大家青島SKF軸承在安裝時應該注意些什么吧！
SKF thrust bearings are mainly used in automobiles, machine tools and other industries. So the installation of bearings must be very careful, because if something goes wrong will certainly have a great impact on our lives. Next let me tell you what we should pay attention to when installing.
安裝SKF推力球軸承時，應檢驗軸圈和軸中心線的垂直度。方法是將千分表固定于箱殼端面，使表的觸頭頂在軸承軸圈滾道上邊轉動軸承，邊觀察千分表指針，若指針偏擺，說明軸圈和軸中心線不垂直。箱殼孔較深時，亦可用加長的千分表頭檢驗。SKF推力球軸承安裝正確時，其座圈能自動適應滾動體的滾動，確保滾動體位于上下圈滾道。如果裝反了，不僅軸承工作不正常，且各配合面會遭到嚴重磨損。由于軸圈與座圈和區別不很明顯，裝配中應格外小心，切勿搞錯。此外，SKF推力球軸承的座圈與軸承座孔之間還應留有0.2—0.5mm的間隙，用以補償零件加工、安裝不精確造成的誤差，當運轉中軸承套圈中心偏移時，此間隙可確保其自動調整，避免碰觸摩擦，使其正常運轉。否則，將引起軸承劇烈損傷。
When installing SKF thrust ball bearings, the perpendicularity of the shaft and axis centerline should be checked. The method is to fix the dial of the dial on the end of the box shell so that the top of the contact is rotated on the upper side of the bearing axle ring raceway, and the dial pointer is observed. If the pointer is biased, the axis and the axis center line are not vertical. When the box hole is deep, it can also be inspected by a lengthened thousand meter. When SKF thrust ball bearing is installed correctly, its seat ring can automatically adapt to the rolling of the rolling body to ensure that the rolling body is in the upper and lower raceways. If the load is reversed, not only the bearing work is abnormal, but also the mating surfaces will be seriously worn out. Because the difference between the axle ring and the seat ring is not obvious, the assembly should be especially careful and not to be mistaken. In addition, between the seat ring of the SKF thrust ball bearing and the bearing seat hole, there should be a gap of 0.2 to 0.5mm to compensate for the error caused by the inaccurate processing and installation of the parts. When the center of the bearing ring is moved, this gap can ensure its automatic adjustment to avoid contact friction and make it run normally. Otherwise, it will cause severe damage to the bearing.
不懂的小伙伴一定要注意了，一定要進來了解一下我們的SKF推力軸承應該如何安裝不要到時候出了問題才知道這些就什么都晚了。
Do not understand the small partner must pay attention to, must come in to know how our SKF thrust bearing should not be installed at the time to know that these are all late.