企業在青島FAG軸承店買了軸承之后，對于FAG軸承的安裝卻并不是非常清楚，這是因為企業內部沒有專業的安裝人員造成的，因此企業如果購買了FAG軸承的話，可以讓FAG軸承的生產廠家派一名專業的安裝人員來幫你進行安裝，這樣就省去了很多麻煩。剛好也可以讓員工進行學習安裝，那么在安裝FAG軸承的時候，應該注意一些什么問題呢?

　　Enterprises buy back FAG bearings, the FAG bearing installation is not very clear, this is because there is no professional installation personnel inside the enterprise, so if the enterprise purchased FAG bearings, can let the FAG bearing manufacturers send a professional installation personnel to help you install, so save I went to a lot of trouble. Just can let the staff learn to install, so when installing FAG bearings, what problems should be noted?

 

　　首先，在安裝FAG軸承的時候，千萬不要直接用錘子或者是其他的一些重物，捶打FAG軸承的端面以及非受力面，這樣會造成FAG軸承部分損傷的，在安裝FAG軸承的時候，可以用壓塊或者是套筒，也可以用一些特殊的工具使FAG軸承的受力面均勻一些，這樣就不會造成FAG軸承單方面的受力了。

 

　　First of all, when installing FAG bearings, do not directly hammer or some other heavy objects, hammering the end face of FAG bearings and non-stressed surface, this will cause FAG bearings partial damage, in the installation of FAG bearings, you can use the pressure block or sleeve, also can use some special tools to make FAG bearings. The force surface is even, so that the FAG bearing will not be subjected to unilateral force.

 

　　其次，在安裝的表面非常好涂上一層潤滑油，這樣就能使安裝更加順利。同時，當遇到過盈比較大的時候，就需要把FAG軸承放在礦物油當中進行加熱，當溫度達到90-100度的時候，就可以將FAG軸承拿出來進行安裝了。

 

　　Secondly, it is very good to put a layer of lubricant on the surface of the installation, so that the installation can be more smoothly. At the same time, when the interference is relatively large, FAG bearings need to be placed in mineral oil for heating, when the temperature reaches 90-100 degrees, FAG bearings can be taken out for installation.

 

　　再次，如果是拆卸FAG軸承的話，也是需要使用一些專門的額拆卸工具，且不可強拆，如果遇到困難的話，也可以使用熱油澆灑在FAG軸承的圈內，這樣在熱脹冷縮的情況之下，F(xiàn)AG軸承就比較容易脫落下來。

 

　　Thirdly, if it is to remove FAG bearings, it is also necessary to use some special forehead removal tools, and can not be forced to remove, if there are difficulties, you can also use hot oil sprinkled in the FAG bearing ring, so in the case of hot expansion and cold contraction, FAG bearings are easier to fall off.

 

　　非常后，有很多人說在安裝FAG軸承的時候，不知道FAG軸承是不是應該先清洗一下，然后在進行安裝。其實在安裝FAG軸承的時候，是應該先進行清洗的，因為在FAG軸承的表面有一層防銹油，只有使用清洗劑把這層防銹油洗掉了，才能涂上潤滑脂，這樣在安裝FAG軸承就是比較好的。

 

　　Very late, many people said that when installing FAG bearings, do not know whether FAG bearings should be cleaned first, and then installed. In fact, when installing FAG bearings, it should be cleaned first, because there is a layer of anti-rust oil on the surface of FAG bearings, only the use of cleaning agent to wash this layer of anti-rust oil, can be coated with grease, so in the installation of FAG bearings is better.